作者查詢 / smartbit

總覽項目: 發文 | 留言 | 暱稱
作者 smartbit 在 PTT [ Electronics ] 看板的留言(推文), 共150則
限定看板:Electronics
[問題] 弱反轉的熱雜訊比強反轉的大多少
[ Electronics ]5 留言, 推噓總分: +1
作者: WetDreamZZZ - 發表於 2022/09/26 12:38(1年前)
1Fsmartbit: 先看看model 準不準,很多舊的製程sub threshold 這方09/26 18:29
2Fsmartbit: 面很差09/26 18:29
[問題] MOS DUMMY大小
[ Electronics ]15 留言, 推噓總分: +7
作者: s055661 - 發表於 2020/10/26 10:45(3年前)
2Fsmartbit: width should be the same for matched layout10/26 15:25
3Fsmartbit: in advance process. length is suggested to be the m10/26 15:26
4Fsmartbit: atched Mos10/26 15:26
[問題] 關於混合信號routing
[ Electronics ]17 留言, 推噓總分: +6
作者: joseph0911 - 發表於 2020/10/05 12:40(3年前)
10Fsmartbit: 如果不做digital calibration , 應該不用走數位流程10/07 21:28
[請益] AB類功率放大器的gain
[ Electronics ]4 留言, 推噓總分: +1
作者: creation - 發表於 2020/06/18 07:06(3年前)
1Fsmartbit: since gain is something of gm. and gm will depend on06/18 21:26
2Fsmartbit: bias condition06/18 21:26
3Fsmartbit: bias conditions depends on output voltage06/18 21:27
[問題] floating well
[ Electronics ]1 留言, 推噓總分: 0
作者: GPaw - 發表於 2020/06/12 21:37(3年前)
1Fsmartbit: nw= max(a,b)06/13 07:48
Re: [問題] Two-stage op amp 設計
[ Electronics ]9 留言, 推噓總分: +4
作者: sa2d61a3 - 發表於 2020/06/09 00:06(3年前)
3Fsmartbit: m3 must be sat. so try to enlarge m1/m2 w/l06/09 05:09
4Fsmartbit: for example w=50u l=0.18u06/09 05:10
5Fsmartbit: if m3 is linear, gain will degraded a lot06/09 05:12
[問題] setup time and hold time
[ Electronics ]12 留言, 推噓總分: +4
作者: jqk147258369 - 發表於 2020/05/08 03:45(4年前)
8Fsmartbit: two different things05/09 11:35
[問題] Layout metal寬度
[ Electronics ]12 留言, 推噓總分: +1
作者: knicks06 - 發表於 2020/04/21 15:43(4年前)
3Fsmartbit: if current density, simulation 是看不出來的04/21 19:15
6Fsmartbit: 而silicon 有可能是過電流燒掉 or 使用壽命lifetime04/21 19:16
[問題] HSPICE模擬crystal oscillator無法起振?
[ Electronics ]14 留言, 推噓總分: +7
作者: woko - 發表於 2020/03/28 23:01(4年前)
6Fsmartbit: try power ramp up03/29 23:45
[請益] 數位和類比的選擇(非常渺茫)
[ Electronics ]25 留言, 推噓總分: +14
作者: herry50307 - 發表於 2020/03/01 20:23(4年前)
6Fsmartbit: 人生其實有很多路口,你現在可以先做你想做的,之後如果03/01 23:53
7Fsmartbit: 真的想轉彎,還有機會03/01 23:53