Re: kern/175670: [iscsi] smartctl fails on SAS disk connected to

On 14-04-17 12:19 AM, linimon@FreeBSD.org wrote:
> Old Synopsis: smartctl fails on SAS disk connected to an Intel C600 controller (isci driver)
> New Synopsis: [iscsi] smartctl fails on SAS disk connected to an Intel C600 controller (isci driver)
>
> Responsible-Changed-From-To: freebsd-bugs->freebsd-scsi
> Responsible-Changed-By: linimon
> Responsible-Changed-When: Thu Apr 17 04:18:15 UTC 2014
> Responsible-Changed-Why:
> reclassify.
>
> http://www.freebsd.org/cgi/query-pr.cgi?pr=175670

I have one of those disks and it works for me in:
   FreeBSD 10.0-RELEASE #0 r260789

# smartctl -i /dev/pass2
smartctl 6.3 2014-04-10 r3888 [FreeBSD 10.0-RELEASE i386] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST33000650SS
Revision:             0002
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
Formatted with type 1 protection
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c50033111111
Serial number:        9XK0JN6Z0000xxxxxxxx
Device type:          disk
Transport protocol:   SAS
Local Time is:        Thu Apr 17 12:36:57 2014 EDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled

This was built from the latest smartmontools developer repository
because the FreeBSD ports version of smartmontool was broken,
see below.

The reporter had Revision 4 of the disk's firmware while mine is
Revision 2. The reported error said the IEC mode page was broken.
No surprise there, mine is too but in a different way:

[root@sas ~]# sg_modes -p 0x1c /dev/pass2
     SEAGATE   ST33000650SS      0002   peripheral_type: disk [0x0]
Mode parameter header from MODE SENSE(10):
   Mode data length=28, medium type=0x00, WP=0, DpoFua=1, longlba=0
   Block descriptor length=8
 > Direct access device block descriptors:
    Density code=0x0
  00     ff ff ff ff 00 00 02 00

 >> Informational exceptions control, page_control: current
  00     9c 0a 10 00 00 00 00 00  00 00 00 01

[root@sas ~]# sg_modes -p 0x1c -L /dev/pass2
     SEAGATE   ST33000650SS      0002   peripheral_type: disk [0x0]
Mode parameter header from MODE SENSE(10):
   Mode data length=36, medium type=0x00, WP=0, DpoFua=1, longlba=1
   Block descriptor length=16
 > longlba direct access device block descriptors:
    Density code=0x0
  00     00 00 00 01 5d 50 a3 b0  00 00 00 00 00

 >> Informational exceptions control, page_control: current
  00     9c 0a 10 00 00 00 00 00  00 00 00 01

The long LBA version says the logical block size is 0
bytes. Well done Seagate!

So IMO this is not a FreeBSD error and most likely not
a smartmontools error. Also it has nothing to do with
the HBA. But I did see this when I tried to build
smartmontools from ports:

[root@sas /usr/ports/sysutils/smartmontools]# make install
make: "/usr/ports/Mk/bsd.port.mk" line 5121: warning: duplicate script for 
target "-depends" ignored
make: "/usr/ports/Mk/bsd.port.mk" line 5118: warning: using previous script for 
"-depends" defined here
make: "/usr/ports/Mk/bsd.port.mk" line 5121: warning: duplicate script for 
target "-depends" ignored
make: "/usr/ports/Mk/bsd.port.mk" line 5118: warning: using previous script for 
"-depends" defined here
make: "/usr/ports/Mk/bsd.port.mk" line 5121: warning: duplicate script for 
target "-depends" ignored
make: "/usr/ports/Mk/bsd.port.mk" line 5118: warning: using previous script for 
"-depends" defined here
make: "/usr/ports/Mk/bsd.port.mk" line 5118: warning: duplicate script for 
target "-depends" ignored
make: "/usr/ports/Mk/bsd.port.mk" line 5118: warning: using previous script for 
"-depends" defined here
make: "/usr/ports/Mk/bsd.port.mk" line 5121: warning: duplicate script for 
target "-depends" ignored
make: "/usr/ports/Mk/bsd.port.mk" line 5118: warning: using previous script for 
"-depends" defined here
===>  smartmontools-6.0 improper use of USE_PERL5.
*** Error code 1

Stop.
make: stopped in /usr/ports/sysutils/smartmontools

Doug Gilbert

_______________________________________________
freebsd-bugs@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-bugs
To unsubscribe, send any mail to "freebsd-bugs-unsubscribe@freebsd.org"